hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I have 52832(ble_app_multilink_central 12.2) which is connected to 5 51822 (experimental_ble_app_blinky) modules.
How to make 51822 not discoverable or not connectable...
Hi, I'm interested in the nRF5 SDK for AirFuel .
I have received a task to replace parts in a product which formerly used wireless charging and the CSR BLE chip.
I think...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hello everyone,
Lately I have been struggling while trying to run "BLE Advertising, a beginner's tutorial". My hardware consists of NRF51822 and PCA1000 dongle. I use SDK_11...
I am working through the TWIS Slave and TWI Master mode drivers Example using SDK 12 with the nRF52832 PCA10040 board and having issues. I am using Minicom through the terminal...
I want to use the last page of codespace for storing a single 32 bit word of non volatile data. I am failing so far and I think I just don't understand the page numbering...
Hello everybody
I am working with the Raytac BLE Module "MDBT40", which is based on nrf51822.
And I am testing example project "ble_app_uart" in the SDK6.1.0 now.
...
I would like to confirm my understanding of Problem sending 6 bytes to multiple services using sd_ble_gatts_hvx
I use nrf52832 sdk13.0.0
BLE SPI is master. I dropped...
Hello,
I connected the nrf module to jlink as described:
• vdd(nrf)-----3.3V
• gnd(nrf)-----gnd
• SDO(nrf)-----SWDIO(jlink)
• SCLK(nrf)-----SWCLK(jlink)
• 3.3V...
I've run into some interesting behaviour in my code and wanted to see if anyone can clarify for me. It seems as though the SPIS module doesn't set the MISO pin as high impedance...
Hello,
I built a simple I2C application for the LMP91000 and I was successfully able to configure it to read the status register.
However, I tested to see if I could...
Hi,
I used to use an imitated Jlink debugger to program/debug my target board(one Nrf51822 on it)
There are pins connection between them,it works just fine.
Now I...
