I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello,
If I use the nRF51822 with 128KB ROM and I connect to a external flash via SPI.
The SoftDevice and bootloader are stored in the internal 128K ROM.
Is it possible...
Using GATT characteristic writes to transfer data is slow.Is there a cleaner and/or faster way to do faster OTA upgrade?
Also I wanted to upgrade firmware without affecting...
I have set up a 6lowpan test environment and could control the led3 and led4. could u please provide me with a code to read value at p0.01. i want to connect a temperature...
I directly connect GPIO pin with 24ohm resistor as follows.
And I set GPIO pin as high drive,
NRF_GPIO->PIN_CNF[MY_PIN_NO] |=
(GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos...
hello ,i use SDK9.0 ANCS project.when I paired it ,it can work normal. it can recive QQ,wechat,message and so on. but when I paired many times, it will be SystemReset.
...
Hi
I am trying to make an activity tracker with very low power conumption with the nrf52. The Idea is to count interrupts from an accelerometer thtat are generated if the...
Hi
I'm testing Buttonless DFU.
I use SDK 12.2.0 , NRF52 and S132.
I succeeded in entering DFU in Master Control Panel (PC application).
I want to do it even on iOS....
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I posted my board before and have fixed the problems another user specified.
I used...
Hello,
is it enough to call NVIC_SystemReset() after I flashed a board so that it returns to lower power consumption? Or do I have to pull out the battery?
Marius
I hope to trigger notification from Bluetooth module into Master Control Panel. I had enabled notification/indication = true. However, when I pressed the button on my module...
Hai
i am able to store one array in flash memmory of nrf51822. but i need to save more than one set of data into flash and retrieve it separately.
how can i save more...
Hello Everyone
Is there any example code which uses indication property. Application nAn-36 uses notification property and as far as i read and understood about indication...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
HI, I have actually couple of (connected) questions,
Can a phone (v4.2 bluetooth) connect to a nrf52840 board that uses 5v bluetooth?
How many (BLE) connections...
