Dear all,
i building the example light_switch_server_nrf52832_xxAA_S132_7.2.0 from solution l ight_switch_server_nrf52832_xxAA_S132_7.2.0 in configuration Debug (SDK nRF5...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hello ! I'm beginning work with BLE . I have a project in which nrf51 is a central. App from smartphone will sending to central any key for example "3214941E0" when central...
Hello Nordic community,
I have a question about implementing DFU on the custom board. By looking at NRF52 DK and reading explanation in Nordic infocenter, I can see that...
Hi,
I am have a custom breakout board that uses the NRF52832 chip and I was able to program it using the J-link programmer and seperating ribbon cable to expose the Vtarg...
How do I maximize range for BT5?
I have two nRF52840 pdk units and I have loaded the ble_app_att_mtu_throughput app and tried it out. I have been seeing around 70 meters...
Hi. I tri to use my soft i2c lib
It works well at nrf51 and other mcu's. But nrf52 i2c_read doesnt works properly.
Other funcs works well.
When i read byte from i2c slave...
Hello
in the zephyr 1.7 release there have NRF52 and NRF51 porting without softdevice .
in the SDK 13 ,there has Freertos example working softdevice ,is there any plan...
hello friends :)
i'm trying to make an nRf51822 evaluation board for breadboard
i used 0.1" header and power from usb connector
i'll upload my altium schematic and...
Hi,
We are doing DFU updates through a nrf51422 dongle (data passing from UART to BLE), using our own code, based on the multilink central example.
The DFU peripherals...
Hi, I'm have a question :
If i download s120 or s130 softdevice, which SDK version i need to download ?
Which version is compatible with my nrf51822xaa ?
The reason is...
Our BLE hardware is designed to send data at 50 Hz speed continuously using nrf51822.
It worked well with APP with Android 4.3 and some Android 5.0/6.0 ,we can receive data...
Hi,
I'm getting familiar with my nRF52 DK (PCA 10040).
I stumbled on something when I was doing an application that toggles LED1 on every TIMER0 event (200ms). Here...
Hi,
Id like to understand the FDS state after flashing the device. Im trying to check if the record exists then I use it, otherwise I write a valid info into the record....
Hello All
Could you please guide me. i want implement BLE with SPI interface...if i sent any command via mobile Bluetooth..then NRF51 DK should receive the Command and...
