Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
I am trying to test the LE Ping feature between two nrf52s. I am enabling the LE Ping feature from one device via:
ble_opt_t opt = {0};
opt.gap_opt.auth_payload_timeout...
Hi,
I have faced an issue during an I2C read operation. My code stuck in the infinite loop of
while (!nrf_twim_event_check(p_twim, evt_to_wait))
{
if (nrf_twim_event_check...
If I understand the nRF52 DK, there's 3 physical debug-out ports on the board. One if for the nRF52 on the DK, which is also brought out through P5. The second one is brought...
I'm implementing a BLE Central based on S132 with functionality for getting a descriptor list from a connected device.
To avoid having to maintain a complete discovery...
Hello folks,
we setup a new Project (eclipse,SKD 12.2.0, S130, NRF51822QFAAH0) based on the sdk examples. But the thing since 2 days we got a error we actually do not understand...
I have a PCA10040 board and downloaded SDK 12.2.0.
I am trying to being a project based on experimental_ble_app_eddystone. I can compile and upload the code to the board...
Problem:
IAR compiled hex file does not work for ble_app_hrs
Environment used:
IAR Embedded Workbench for ARM 7.80 Kickstart evaluation
nRF52 DK
Observation...
Hello,
I use, with success, the FDS library to save data to the flash memory. I also use, with success, the bootloader to update the application (original dual bank ble...
Hello there, thanks so much for taking the time to read. My problem is the following
I am trying to run GZP (Gazell Pairing Library). After successfully pairing with a...
We are currently trying to log our sensor data to a mobile phone through uart using nrfLogger app. We have nrf51 module and we are using SDK 12.
In nrfconnect, we select...
Hi,
I have problem with long write by sd_ble_gattc_write.
I send first 18 bytes by button on pca10028, then I waiting for BLE_GATTC_EVT_WRITE_RSP and sending rest of bytes...
I need some help with something very basic...
I need a way to upgrade my DFU BLE bootloader to either reset back to the app if no update has been sent after some timeout...
hello,
According to the "twi_scanner" example from the SDK12.2 I don't understand how the respective I2C pins/GPIOs are set up.
There is this function that I found "nrf_gpio_cfg...
