Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Is MTU of all BLE devices limitted to 23 bytes when using ATT protocol?
I don't know explicitly.
Some say it is possible to use MTU longer than 23 bytes.
Others say...
I am using TAIYO-YUDEN EYSHCN, which is having Nordic-nRF52832 chip on it. As per document from TAIYO-YUDEN, recommended to flash s132-firmware on it. I downloaded s132_nrf52_3...
I have two questions with the remaining unresolved symbols being the most critical. I will decribed the situation I have encountered as a sequrence of chronological steps...
Hello,
I have a need to construct multiple portable devices on a short time frame. We expect that building Arduino-format shields for our peripherals and using nRF52 DK...
I am using PWM on a BLE Nano using Nordic SDK. I was having problems with the PWM and decided I would set the duty cycle to 0 to see if the program was working right:
#include...
I'm trying build a file in Keil, and have received this error below. Please advise on how to fix it! Thanks!:
*** Using Compiler 'V5.06 update 3 (build 300)', folder: ...
Hello,
I'm trying to put a BLENano board to slepp every loop iteration. These are te steps:
setup:
sd_power_mode_set(NRF_POWER_MODE_LOWPWR);
NRF_POWER->TASKS_LOWPWR...
Can someone tell me the best way to build the old bootloader under SDK 12.
Looking in the examples, in SDK12, there is now only the bootloader_secure example
SDK 11...
Hello
I want to know if we can wake up nrf52832 in sleep mode , from a command through an application on a phone via BLE. If its possible can someone please guide me to...
I want to add backtrace functioanlity in nrf52. I am using functions given in below link:
link text
But I am not getting library files for defining functions mentioned...
Hi,
I have programmed a BLE code.
In the code we are continuously connecting and disconnecting BLE connection.
The BLE connection is established for around say 1 sec...
hi,
This function is called on BLE Event when someone writes to RACP characteristic
What i woud like to know is, is it called from any ISR routine?
Or when BLE Event...
The radio mode 250Kbps is removed from nRF52832. However, by our test, nRF52832 radio can still work with radio mode 250Kbps with setting
NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_250Kbit...
Hi All,
I have a question about the SPI pin number on nrf51 Dk.
I don't understand when i look into the pca10028.h file, i see this mapping:
#define SPIM0_SCK_PIN...
