Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hello,
I'm redrawing and routing my own PCB for nRF81x22. I take the details from pca10028 files.
My question: Can I route the PCB with only 2 layers?? I have seen only...
Hello,
I had to use sd_ble_gap_address_set() to make sure, that a bootloader running on the same device will not be cached on OS/X:
static const ble_gap_addr_t gap_addr...
This may be a newbie question, but it had puzzled me for a while now.
Looking at the PCA10031's schematics i can see two leds been used.
LD2 i can figure out. Datasheet...
MQTT Example in the IoT SDK compiles with size bigger than available 160KB Program space?!! Is this correct as I can't flash with the IoT SoftDevice on it.
The drive level of the nRF51822 is specified as 1µW, whereas the EPSON crystal suggested in the BOM for the EK boards PCA10000 and PCA10001 is specified for just 0.5µW (with...
hi nordic
i just got a little bit outdated "nRF51422-dk" package. I have problems with flashing
the boards pca10006 and pca10007- I tried to search for an solution, tried...
Hi all,
I'm an Android developer and I need to develop an application that detect when someone presses the button on Beacon and do something.
I've just bought these two...
I'm currently using ble_advdata_set to update the ble advert data packet. Before transmission I use the ble_radio_notification event . In this event for test purposes a single...
Hi,
I'm using a nRF51422+nRF6310 and I need to use SPI in order to connect with some devices. I am trying to run the example "spi_master_example_with_spi_slave" but I found...
Hello, I'm using IAR for ARM 7.1.
I made my own project and I want to make my project as a hex file to
program my application to several boards.
/***************...
Hi, i am currently modifikat a working ANT-System (Master with multiple Slaves) with the NRF51422 and Softdevie 1.0 to be robust against in band disrupters. My idea is to...
I have an application based on the ble_HID_keyboard_template (uses STM32F072 instead of Arduino). The first time I pair my iPhone 5 (iOS 8.1.1) with the nRF8001, everything...
