I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
I have compiled the ble_app_uart sdk the nRF51 SDK_v5.2.0.39364. (see attached file)
and I upload this app to my device using OTA .
I found it can work with my Android...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
HI:
It is correct that call the function nrf_nvmc_write_word at nrf51_sdk_v4_4_2 and s110_nrf51822_5.2.1。
void FlashWRPProcess(void)
{
#define NRF_UICR_RBPCONF_ADDRESS...
S110 define UUID rule as below, it just can modify one word.
Services UUID = 0x49535343-FE7D-4AE5-8FA9-9FAFD2-5E455
Characteristics UUID= 0x49530001-FE7D-4AE5-8FA9-9FAFD2...
I have programmed custom services on my evaluation kit and everything works great. I am now looking to implement updating my application from iOS and Android app.
Using...
Hi,
i have a question relative to the configuration tool File Format.
I'd like to modify (automatically) the configuration file in order to change the "Device Name"...
I am using a Bluetooth NRF 8001 module. I want to send data to the module from my android phone to the bluetooth module connected to an Arduino. For sample test I used nrf...
Dear Håkon Alseth,
you posted twi source code which took care of all SD/PPI stuff here and it was also linked here , but it is no longer available. The whole forum seams...
Hello,
I use the bootloader in SDK v5.2.0 and could not run APP after DFU completed.
It always stay in the DFU state.
After checking the memory by J-Link commander, something...
At work we are primarily interested in using the 128kb nRF51822 devices. I am able to get a softdevice and bootloader onto a 256kb device just fine. When I attempt to do the...
Hello all,
I want to send some sensor data( collected by Pic controller) to other BLE client(may be a phone) using nrf51822 via UART. Can somebody suggest how to communicate...
Hi,
In the reference design of "nRF51822-QFAA_ST_BAL-NRF01D3", the datasheet recommends this crystal ( www.digikey.com/.../3125558) , but we are out of stock from local...
Hello all,
I have flased "ble_app_hts" example for nrf51822 on evaluation board PCA10001. In the application both the LED pins are configured for output using "nrf_gpio_cfg_output...
I have a large array of uint16_t data to use as a lookup table, which is defined in flash. It's 4002 bytes in size, and I can set where in flash it is saved. I'm accessing...
