I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Is there a step-by-step setup for the nrf52 developer kit for Mac (OS X)?
For example, when I connect my DK board, it does NOT appear as a USB drive which is the very first...
I've read through the 'streaming' posts and my need is a little different. I only need about 30 kbps streaming. I've created a service of this but am quite new to BLE and...
Hi all,
Is it possible to check whether there is an active carrier with the nRF24L01+? I've got the TX and RX chips configured via SPI correctly (I think), yet I can't...
What do I need to take care of when I solder CE pin to VCC? (to save I/O)
NRF is mostly in RXing state, and sometimes TXes.
So far I figured out to go from RX->TX mode...
Hi,
Can I use RTT to build a communicate to a command line interface (CLI) in the device?
This would require that the program does not block, as it does in SEGGER_RTT_WaitKey...
I'm using the UART application in nRF Toolbox Version 2.4, iOS 8.4 on an iPhone 5S.
Is it possible to save the logged data to a file, or in any other way get the data out...
Hello,
I am using an Eclipse GCC environment with the following setup:
Ubuntu -> 14.04 (Trusty Tahr)
Eclipse IDE for C/C++ Developers -> Version: Luna Service...
kit: RF51DK.
sdk:nRF51_SDK_8.1.0
SoftDevice:s110_nrf51_8.0.0_softdevice.hex
I want to use 5 channels pwm to control 2 servos and 1 motor;each servo uses 2 channels pwm...
I included the DFU service in my project. With the MCP on my computer it is working fine.
But when I try to perform the DFU over the MCP(v.3.4.1) app on my android device...
I'm migrating firmware from SDK 6.x to 9.0.0
I found pretty many changes in SDK APIs.
Do I have need or do you recommend to upgrade to new SDK ( for bugs / problems...
Hi!
I'm working with nrf51dk with s110 Soft Device.
I need to read ADC every 2ms. In order to achieve that, i made timer with interrupt after 2ms. here is my code of initialising...
I have a quick question about the use of the nRF51 DK's Debug Out port (P19) to program external nRF51 boards.
The user guide says that the DK will "detect the supply voltage...
I have some questions about 2.4G protocol stack gazell&ANT+&BLE .
gzll&ble :
choose nrf51822 ，and use S130 SOFTDEVICE,then we can achieve gzll&ble coexitance. is that...
