Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi
I don't have the board space for a loop antenna, so I'd like to use a dipole. What sort of RF output / matching stage do I need for this on the nRF905?
Thanks!
Hello
I wrote the program by referring the some examples after compiling the program GPIO pin becomes high immediately (3.3V ) bu my aim is to make the GPIO pin as output...
I have two nrf24l01+ modules communicating on a single channel. The "remote" does 99% of the data transmission while the "base" receives and uploads to a host. Occasionally...
How to use stlink or CMSIS - DAP downloading S110 protocol stack? Jlink can use nrfgostuide down s110 protocol stack, i want to know how to use stlink or CMSIS - DAP download...
Hello,
Is there any information on current consumption for the nRF51822 when running the micro-esb examples? I'm curious as to how much current is being used in a situation...
I'm testing a custom board I did. The board has this 16Mh crystal
geyer-electronic.de/.../GEYER-KX-7_01.pdf
The CL of the crystal is 12 pF. I'm using a pair of capacitors...
Hi,
I am trying to get the ble uart example from the sdk 0.9.2 working on my nrf52 DK board.
But the nRF UART v2.0 application on my android phone, quits instantly after...
Hello,
I'm looking to send a 32 bits word to the example "LebButtonDemo", using an iPhone application created with Evothingd Studio (it uses Javascript).
I'm able to...
Hello
at the moment I have a running S120 BLE firmware update on my nRF51822 hardware.
This works fine on my desk.
But we have the additional requirement to update the...
Hi
I have an custom board which uses an nrf51422 SOC. I am facing issues with my radio.I use an softdevice s110 with an application on it.
The code just works fine with...
Hi Noedic,
I triggered the DFU function through APP, the device restarted and the base service UUID changed from 0x0001(nus function) to 0x1530(dfu function), but it is...
Hello,
I am working on S120 SD v2.1.0 for central and S110 v8.0 SD for peripheral and SDK9.0 and I am able to configure 1 single uuid on central and connect to multiple peripherals...
Hi.
I would like to konw some ditails aboute nRF9E5 device:
What is the rang between 2 devices using 433 mhz.
do you have any samples codes ? i need to trasmitt...
Hello,
After i disable SD i try to count ticks on TIMER1 from RTC1 via PPI.
Timer1 is configured property but TASK_COUNT don't increment cc.
I see that event TICK on...
