I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I set up a 2 GPIOTE interupts like this:
in main.c:
APP_GPIOTE_INIT(3);
err_code = app_gpiote_user_register(&mainUser, 0x00000000, (1 << RF_GPIO2), powerButtonInt...
Hi
I am using sd_ble_gattc_primary_services_discover(conn_handle,0x0001,NULL) to discover primary services on a GATT server. After the first call to this function, I get...
In nRF51 PS, I read typical/max time for AES ECB are respectively 8.5 and 17µs.
What would be those values for the whole AES-CCM operation (ie including MIC computation)...
Hello,
I'm working on a software we've made starting from the "ble_app_uart_s132_pca10040.uvprojx" source code. My "main" (procedure fct) is in the for (;;) of the void...
Hi,
A couple new fixes in listed files to supress gcc errors when -flto enabled.
hardfault_handler_gcc.c
port.c
Patches are in answer below.
Regards,...
I´ve read that the command "lib_aci_close_remote_pipe" is not available on the chip NRF8001 build code C. I need execute this command to solve a bug in the ANCS service. If...
Hi
I have setup and configured Eclipse using the tutorial and all seems to be good, except, I cant flash the binary to the chip. Here is my error when calling flash:
...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
We are using your nRF24l01+ chip in one of our products. we are using 1 nRF as receiver and 5 nRF's as transmitters.
While trying to use the chip with multiciever configuration...
Using SDK13 - I would like to use the fds/fstorage libraries, but I'm told that "The experimental label is due to lacking test coverage for the two modules". here
At the...
Hi,
I've been suffering with detection of writing to cccd to enable notifications. The S132 (nRF5_SDK_13.0.0_04a0bfd + s132_nrf52_4.0.2_softdevice) never fires BLE_GATTS_EVT_WRITE...
Hello, I'm migrating a project from nrf51 to nrf52, and there is this function:
uint32_t dfu_init(void)
{
m_cmd_handler = *((bl_if_cmd_handler_t*) (0x20000000 + ((uint32_t...
