We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi, I have a Nordic nRF52 Development Kit. The ADC examples work, the LED examples work, and the NFC examples work. However, none of the Bluetooth examples work. The LEDs...
My DevKit arrived today. Very nice.
Plugged it into my mac, immediately recognized as USB device. Flashing LED, mounted as storage device, etc.
Tried to enter Bootloader...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello everyone
I am trying to configure the write values like in the link loss profile it is possible to write no alert, mild alert, high alert, similarly i have created...
Hello!
I would like to know if it is possible to send an unique Gatt message that contains notification enable for multiple characteristics.
For example,
buf[0] ...
Hi Nordic,
I posted the issue with BSP package in devzone.nordicsemi.com/.../
unable to attach the main.c file mainOriginal.c
HI Aryan,
Thanks for your reply. Its working...
main.c HI Nordic,
I don't want bsp.c in my project. So I removed the bsp.c and included custom_board as mentioned in devzone.nordicsemi.com/.../
I am also using UART for...
I have the nRF52 dev board "PCA10040".
I downloaded "nRF52_SDK_0.9.1_3639cc9" SDK.
I noticed that there is no installer for the SDK.
I unzipped the SDK and using Keil...
Hi all,
Since I will use broadcast way in RF transactions between one NRF24LE1 based senders and serveral NRF24LE1 based receivers . I was told not to use "Auto ACK" in broadcast...
I'm new to Bluetooth LE, Python and C. I have the S130 python examples for heart rate testing. I am attempting to modify the heart rate collector code to act as our central...
I am able to use pstorage_clear and pstorage_load without any problems, but whenever I try to do a pstorage_store the callback function is not being invoked. This problem...
-Essentially I want to do a device firmware update on to the nrf51422 using my Android phone (the nrf applicaiton). I am using your sample code for a project that my company...
Dear All,
what example would be best starting point for a transparent COM port over the air connection with nrf51422?
We will require 9600baud and there will be custom...
