Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I am using timer interrupt in my code. In that I will be generating interrupt after certain time interval, after the interrupt it should process the incoming data from...
Hi
We are using the nRF52840 and the application is OK now. Then I do the OTA using a Android phone which supports Bluetooth 5 and it's made in our country. I use the nRF...
Greetings,
I am using nrf51822 (experimental_ble_app_eddystone example from SDK). I am advertising UID ID namespace and UID ID instance. I am able to see the data in nRF...
I am working on a project that uses PIC18 and nRF8001. PIC18 is used to control nRF8001 and LCD. The project needs to transmit large data to central ( about 512KB). It seems...
I have some improvement I would like to see in the stack. How can I get these implemented. Improvements include:
Allow advertisement reporting events during connect...
I am not sure if this is the right forum to ask this question but I can't find details on availability and pricing for nRF52840. I tried calling DigiKey but they don't have...
Hey guys,
With the ble_app_exemple, I manage to add the FDS libraries. Unfortunately, when i run the example in Debug, I got error 2 for fds(FDS_ERR_NOT_INITIALIZED). I'm...
Hi,
I am using nrf51822 module and sdk v12.2.0.
I was compiling code under ubuntu. I observed that pca10028 is configured for nrf51422_xxac target.
But i want to use nrf51822...
Hi,
The NFC function is set to read only in my application. I don't want to wake up my system when someone tap on my device to read the NFC data. (assume this method can...
Could someone confirm whether there are schmitt triggers on the nRF51822 GPIO. I found the following thread that mentions them, but it also is discussing the nRF52 series...
Arm Gcc (using Eclipse Neon) |
SDK 13.0 |
nrf52 DK (PCA10040) |
tried soft device 4.0.2 and 4.0.4
I can successfully compile and run the example -ble peripheral- ble_app_hrs...
Are there any particular practices or instructions should i follow if I want to write a custom library
We are trying to write a library for LEACH protocol and it is a network...
I spoke with someone at Nordic who seemed to imply that utilizing the radio does not necessarily tie up the Cortex processor on nRF5X devices. Is this true? It seemed to me...
I am trying everything.
In sdk_config: #define UART_DEFAULT_CONFIG_HWFC 0
In the nrf_cli_uart.c I changed it to APP_UART_FLOW_CONTROL_DISABLED,
in the pca10040.h I...
