Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
In the \external\micro-ecc\micro-ecc folder，when i used ”build_all.bat“ to build target，it happened “makefile:83: *** missing separator“ error
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
To the kind attention of Nordic support team,
I have been reading https://infocenter.nordicsemi.com/pdf/nRF52833_PS_v1.0.pdf product specification, where only
aQFN 73...
Hello everyone, I wan't to layout my own PCB board of nrf52840 ,is there any things need to be attention? By the way, if I'm not using Interface IMU to upload my programming...
When I have put the nRF9160 modem into mode 4 or 44, and then issue a status read AT+CFUN? command, the modem erroneously goes online. I have used latest and greatest modem...
