Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
HI,EVERYONE,
NICE TO MEET YOU,
i wanna know that if the buttons_leds_init assigned three buttons at once.
And i noticed that the function name is 'advertising_buttons_configure...
Hi All,
We are in design phase of our project, which uses two NRF52 chipset one as master and Central , We have some prewritten content in Flash, which need to be read...
I ´m testing gpiote interrupt, i´m work with nrf51-dk, softdevice S110 and sdk 9.0.0.
I have a pin that receives a signal 0 all time, and it changes to 1 when I have to...
Hi, I'm using SDK 7.2 and S110 7.1.
I haven't mirgrated to SDK 10 yet.
I'm using the HRS and bootloader (which uses dual bank and BLE OTA) example.
After I select...
I am using nRF51 with Softdevice S110 to do a BLE peripheral, I want to have pin-code authentication before central device (or android phone) can connect to the peripheral...
ble_app_hrs_rscs_relay.hex the application ble_app_hrs_rscs_relay in SDK v9 can run fine,but in SDK v10.0.0 it doesnt work,even when i debug , it cannot go to main, and i...
Hi.
I have troubles.
I'm using nRF52 DK and V0.9.0.
I'm making program that does TWI communication between MPU9250 what is 9-axis sensor.
error is false every time.
...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
