The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
I am trying to connect thingy as peripheral and many smartphones as central but i can connect only one smartphone by using thingy at a time.Is it possible to connect many...
[References]
In page 234 of nRF52832_PS_v1.4 it says "In both modes, the TIMER is started by triggering the START task, and stopped by triggering the STOP task."
In this...
I am trying to add a custom service to support a communication path in my project. The Nordic UART example gives a good place to start so, using that as a template, I have...
Hi All:
i met a trouble.
i want to implement a function that i can restore mesh device by uart cmd.
so , i add uart to light switch service demo, when i recive a cmd...
Hi,
I tried the BLE Uart example on my own nRF51 board, but after a few minutes the application hangs in the softdevice.
The board is one we developed, an FTDI cable...
Is there a way to retrieve 128-bit base UUIDs from the SoftDevice, either the "built-in" Bluetooth SIG standard or a vendor-specific one registered via "sd_ble_uuid_vs_add...
Hi,
I'm having problems running the ble_peripheral/ble_app_blinky example with my iPhone 7 and nRFConnect. Here are the specs for the tools I'm using:
nRF52-DK: PCA10040...
