Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello
I adapted the ble_app_uart with twi functionality.
Therefore I included the "app_twi.h" which includes the "nrf_drv_twi.h"
But as visible in the picture, the "nrf_drv_twi...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
2017-03-01T12_28_45.220Z-log.txt Hi,
we experience an issue with the PC-based nRF Connect tool, details are as follows:
we use scan to discover BLE devices,
we...
Hello,
I'm actually working with a custom profile generated with Bluetooth Developer Studio. I'have some difficult to send characteristic with the template.
My setup...
I have a created a bootloader using the bootloader_secure example in SDK 12.1. Using my own public-private key pair I've created two zip files, signed with nrfutil, one with...
I'm modifying 'ble_app_uart' project with custom board.
And also test with Android app that Nordic released.
I'm wondering how to set this connection "bond".
Does Nordic...
Hello all,
I little confused with these two examples as mentioned in my question. Both examples are different and their use case is also different. Can somebody please...
Hi!
Faced such an anomaly. In 2-3% of cases when exchanging PTX device sees a transmission error (the ACK did not come) and device PRX is not see this error.
Is there...
These pins do not work when I connect to nRF51822 module directly..
Like this. I cennceted VDD, SWDIO, SWDCLK and GND to nRF51822 module.
And there are not jumpers to...
Is there any sample code in examples, because am a newbie to this great platform, my objective is to glow an led , when the motion is detected , and also when there is no...
Hi Sir,
I add NUS service into CSCS project base on nRF5_SDK_13 follow the steps below, there was no error occurred after build the project, but it didn't work. Please...
Hello,
I'm trying to set up I2C with an mCube cccelerometer, which has an I2C 7 digit ID of 0x6C and an 8 bit address (write) of 0xD8.
With the code below, I see on...
Hi.
I have a custom board, which I power up via AAA battery through a buck-boost converter. I wan't to measure battery level using on-chip ADC only on requests from master...
