NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hello,
I am having much fun with nrf52. I'd like to implement SPI read (few bytes) per GPIOTE event over PPI, the source is the GPIO event and the destination task is a...
Hi,
I'm working with the nRF51822
I'm trying to enable the use of some timer callback on the ble_app_template.
I've succefully created and started all the timers, but i...
I have a modem connected to some pins on an nRF51822 on a custom board. Two pins on the modem are active low. One is a reset pin, the other a VCC control. I want these pins...
Can the nRF51822 DEC2 pin (LDO output) be used as a 1.8V supply for low current use (say, <50uA)? Similarly, how about the 1.9V output of the buck converter (AVdd)? The current...
I'm wondering if the latest version (8.x) of S110 supports BLE 4.1's "Connection Parameter Request Procedure". This procedure is described in the BLE 4.2 spec Volume 6, Part...
I previously used Jlink to upload code to my nrf51. However, the new units I got are "locked" and I need to use nrfgoStudio to unlock and fully erase the chip.
Is there a...
Hi, I wrote a sample application to remotely control and led on nrf51822_xxaa module. in the application I was able to provide configuration to the characteristics as well...
Happened to try nRF master control panel service App.
It is a good tool.
But there probably something missing in "Scanner" screen.
I used heart rate example to do the test...
After seeing a few answers here (and elsewhere) which were very helpful to understanding the scope of my problem:
devzone.nordicsemi.com/.../
forums.adafruit.com/viewtopic...
Hi,
I'm developing a hid keyboard + lbs(led button) application, in my design there're several primary services and each with different characteristic(with read/write notification...
when upgrading from SDK8 to SDK11 every SVCALL to the softdevice now just jumps to the application's weak SVC_handler and "B ." spins.
I can make a main.c file with only...
Can we have one application to Modify both iBeacon and EddyStone properties? (App development in Android)
Greetings,
Will we be able to support a modify beacon props of...
I need help sorting out a configuration.
What I want to accomplish:
phase 1: detect if any bluetooth phone/device is present, without connecting to it
phase 2: determine...
