Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello, first of all: I do not expect support from nordic here, but if any kind sole could shed some light on this, I would be very grateful. I’m developing an open source...
Hi All,
I was tasked to create a program in visual studio that can just detect the 949-NRF51822-BEACON
Using the 949-NRF51-DONGLE. A simple application that detects the...
Hii all,
I wanted to generate a clock pulse from the pin P0.05, I've written the code and when I tested the application with nrf51 DK with chip 51422-AC its working fine...
Hey everyone,
I'm trying to send a value as a notification packet from GATT Server (slave) to GATT client (master) at 7.5 ms connection interval. I have set up the radio...
I am using a simple 4 by 4 matrixed keypad, and I would like to handle some of the decoding myself.
In essence, I would like to configure all 4 rows as low driven output...
Hello,
I already searched the forum, but I didn't find anything.
Is there a way to invert a port on a NRF51822?
I use this chip together with an XMega-Chip and they...
Hi,
I'm trying to get PCA10001 board working. I used ble_app_hrs example from SDK 6.1.0 (I'm using eclipse with gcc). The Softdevice is v7.1.0
The application seems...
I have a nRF51DK with SD 8.0 flashed.
I would like to start and stop a pwm signal with the buttons on the board(BUTTON_1 and BUTTON_2). The pwm is working fine. But when...
Hello:
I want develop my nrf51822 project base on new sdk and softdevice.In /nRF_Examples/9.0.0/ble_periphera/ble_app_uart/, the keil project device is nrf51422,and it can...
Hi,
I'm compiling the simple blinky example with no softdevice for an NRF51822 xxAA using GCC on linux. I can't get any LEDS to blink off the GPIOs, so I'm debugging with...
I can see a phrase "Not recommended " on the Evaluation Kit's page: www.nordicsemi.com/.../nRF51822-Evaluation-Kit
What could that mean for me if I already have the kit...
I found in ble_app_uart example, any device with UART app can connect to uart service and send something to COM port or just block the connection of other devices.
So can...
I'm trying to update my firmware using the dfu, I tested two examples of the SDK :
one of them is dfu_dual_bank_ble project,
I noticed that the memory allocation...
Hello,
I have been reading a lot of Nordic and DevZone stuff. The information I need appears to (almost) be there but I cannot quite put it all together. I need some help...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
