Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi, I'm using SDK 7.2 and S110 7.1.
I haven't mirgrated to SDK 10 yet.
I'm using the HRS and bootloader (which uses dual bank and BLE OTA) example.
After I select...
I am using nRF51 with Softdevice S110 to do a BLE peripheral, I want to have pin-code authentication before central device (or android phone) can connect to the peripheral...
ble_app_hrs_rscs_relay.hex the application ble_app_hrs_rscs_relay in SDK v9 can run fine,but in SDK v10.0.0 it doesnt work,even when i debug , it cannot go to main, and i...
Hi.
I have troubles.
I'm using nRF52 DK and V0.9.0.
I'm making program that does TWI communication between MPU9250 what is 9-axis sensor.
error is false every time.
...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
Hi. i use SDK 9.0.0 and S130_1.0.0.
I want to recieve data from My peripheral S110..
First, I try to recieve data using example "ble_app_uart_c_S120-master".
I could...
Conditions in www.nordicsemi.com/.../Why-can-Master-Control-Panel-not-find-my-Master-Emulator-Dongle have been met, ie all components of PCA10031 have installed successfully...
in the answer of this question it said that :
You are also not allowed to send a new
indication until the previous one is
confirmed. This is signaled by the
reception...
I found this: github.com/.../nordic-nrf52832-gcc and tried to add it (and its dependency to the nordic-nrf52832-gcc 0.1.0 target to yotta with no luck. Is there a description...
