Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
Hi,
I'm trying to use the nrf52832 with a sdcard application in SDK_13. I based my code on the example provided and managed to get the sd card working without any problems...
The error "Unknown command add_pc_lint" appears when running the bootstrap command during setup. It looks like PC-Lint is an application for windows for software debugging...
Hello! I'm trying to find a list of boards that can be integrated into a circuit design which have already received compliance in the EU, UK and with the FCC. I found this...
Hello. i testing zigbee coordinaator example with zigbeee device. Device was joined to Zigbee coord/ network.
Couldn't i get device payload data in coordinator source code...
I have the UART configured using the standard boiler plate code, with flow control enabled, where the RTS output is assigned pin 5.
I have defined a GPIOTE pin 25 as an...
We are working on a solution that involves a central provisioner that provisions a MESH network of sensors that it subscribes to. We need to be able to replace this central...
Hi,
I am currently drawing up a schemtic involving the NRF52832 on Proteus 8.
I have been trying to find symbol, footprint, and 3D models of the NRF52832 online, however...
Hi!
We are using a custom bootloader for our device. Current version of this erases everything from 0x0 to bootloader start address, and then writes MBR + Softdevice ...
Hi,
I have a question about ADC reading in ble_app_uart__saadc_timer_driven__scan_mode in SDK 14.
Let's say I'm using a double buffer, and I have 3 ADC channels (so...
Hi,
In my project, I am use nRF52832 for controlling ws2812b led strip with 8 leds.
I am use SDK 14.2 and s132_softdevice_5.0.0.
I have problems with the latency of...
I have a custom board of nRF52832-QFAB-B0 on which my application works well with SDK15.0.0 & SD132 v6.0.0
To perform DFU,
1. I copied the relevant parts of ble_app_buttonless_dfu...
There is always one kid in the class who wants to correct the professor and make himself look special.
That is me.
So: In file nrf_sdh_ble.h, line 76
@details This macro...
