Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hello guys!
I got a board of nRF52 with a Jlink debugger on it through a serial port and I program it with nrf-connect-mesh-official-serial-gateway-fw.hex.
However, when...
I am programming a Ble Nano device using Nordic SDK. So far I have been using examples from the ble_peripheral and ble_central directories. Now I want to run an example that...
Hi,
I used the nrf51822 as the spi master,it could send out the data, but it didn't receive the slave data.Did I miss somthing?
static volatile bool m_transfer_completed...
I'm working the the NRf52 dev board and SDK12.2. I was able to successfully load the standard DFU example and then use the NRF Toolbox on an android to load the example HR...
Hi.
I'm getting an nRF Dongle (PCA10031) set up on a Windows machine to be the BLE central that we'll use for our production line testing. To that end, I've built the pc...
The pc-ble-driver project uses CMake to generate Solution and Project files for the Windows build of the project. CMake uses absolute paths in these generated files. I can...
Working with nRF52832 and SD132-v2.0.1
Using Timer 1 at 1MHz (pre-scale 4) and 32bit bitmode CC to trigger events at a pretty wide range (from us to minutes).
I'm getting...
I am calling certain services and I can see this output on my UART listener:
0.000013 : UART Start!
0.385355 : BLE Stack Initialized
0.385581 : Peer Manager Initialized...
What would be the best value for UART buffer?
When I put it as 512 it gets crashes, below you can see the putty output
0.000013 : UART Start!
0.415937 : Handle list for...
I want to use app sched feature, so as example does, I call:
static void scheduler_init(void)
{
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE, SCHED_QUEUE_SIZE);
}
since...
Hi Team,
I need to make an application that we receive a data from a chip through UART and need to send the data to Console through another UART. Is it possible to make...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
Hi all,
I'm starting with fcc and etsi test! i know that the radio test example is useful to test the radio.But the ETSI add two type test about receive emission spur and...
Hi!
So I managed to create my custom service with one characteristic (a struct with several attribs).
I can see it in my app and everything's awesome. Yay.
But in some...