Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
I tryed to find in Q&A something that can help me understand how it is possible to measure battery voltage with nRF52, but i am not sure i found the exact explanations...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
What hidden settings am I missing this time in the awful Segger studio ?
I get an error :
unknown type name class
When I compile with this new class called...
hello i am new to spi, i am doing project on 3 wire spi interface. I am using 3 wire interface as Sclk,ssn,MOSI pins only , I am not using MISO pin .I am tested spi example...
hello, I am working on nRF52 DK spi protocal.I am using AD9837 as slave.Here i am using 3 wire interfacing.I am connecting Sclk,ssn,MOSI pins olny & I am not connecting MISo...
what's the maximum data rate of nrf24l01+ (with ACK and without ACK) using 2 nrfs?
if i use 4 nrf24l01 two in tx side and two in rx side.what would be the maximum data...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
Hello all,
I need to program nRF52 via the SWD pins. I cannot use the nrfjprog or J-link or Segger etc. I have connected 3 wires to the nRF52 - SWCLK, SWDIO and GND.
...
Hello to all
I'm working in an application that needs to be completely power optimized. In this program the device works as a scanner that if it finds an specific device...
Hi, I am wondering about the pre-made PCB's available on ebay, with a nRF24L01+. At a cost of $1, and with various forum stories over the Internet referencing issues such...
I am using NRF51422 S130. I have a master SPI configuration set up, and not using Nordic spi drivers provided in the examples. I think my configuration is correct.
1- I...
Hi,
We started out developing an application using the SoftDevice 1.0.0-3 (from SDK 0.9.2). We now need to upgrade to SoftDevice 4.0.2 (included in SDK 13.0.0).
We already...
Hello, I have some ideas to do for IoT and bluetooth. Already did some tests with MQTT raspberry pi and ESPs SoCs. Then I started to dive into bluetooth world and I found...
