I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I use s110 send notification to s120 in 1 - 1with 7.5ms connect interval,but the data maximum data throughput is only 21.3 /2 kbps.how can i do to raise the throughput???...
i use s110 send notification to s120,and set connect interval with 7.5ms,but in actually the connect interval is 15ms!!I see s120 softdevice specification,s120 as client which...
Hi,here i met an issue that when i set address type in public mode by funtion sd_ble_gap_address_set(),and then the advdata packet data was all zereo.This project was created...
Dear ladies and gentlemen,
There is not much information about the RESET pin in the datasheet. I guess, it doesn't have an internal pull-down resistor, but when I look at...
Hi,
I have a problem configuring readback protection using boot.
It seams that the BOOTLOADER stops when trying to read some information from the softdevice if readback...
HI:
i want to use peripheral and central function.and i can switch it to work peripheral or central state when i need.which stack should i use.s120 or s130.
I am using CMSIS RTOS (RTX) to implement an application for the NRF52 DK. I have found an error in the SVC handler that results in a hard fault when calling a soft device...
Hi all,
I was trying to use the S130 Softdevice but the uart peripheral doesn't work properly... I am trying to send three bytes, but only one appears. Flow Control doesn...
I am using a mutex to protect a serial debug printout.
Is it safe to use sd_mutex_acquire in a blocking manner, provided it is only called from main and softdevice callbacks...
As suggested in another post , I asked to our Nordic dealer about nRF52832 chip availability.
Thay talk about 2015 december for mass production , as your direct info confirm...
When i setup DEVICE_MANAGER_MAX_BONDS in 2 and trying to connect third device the nRF 51422 (10028) is freezing and all LED's light up. Why the algorithm in "device_manager_evt_handler...
Hi
I managed to integrate the buttonless DFU example, but while testing it, I have a few difficulties.
I use Lightblue to access my services and enable notifications...
Hello There, I want to connect two slaves to my nRF51422 PCA10028. I came up with the idea of using two master communications which share MOSI AND MISO but have different...
Can the chip be updated from an ANT device to a BT Smart Central. This means it starts its life with an S210 and then gets a serial code update to an S120. Obviously with...
