I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi all,
There are lots of posts on the devzone about adding DFU service to a custom application and they have been very helpful in getting to this point.
At this point...
I was looking into changing the S130 attribute table size, which is by default set to BLE_GATTS_ATTR_TAB_SIZE_DEFAULT, and noticed that this default seems to be set to zero...
Hi,
I have programmed my nRF52 DK using the ble_app_beacon example from SDK 14 along with S132 V5. I have set NON_CONNECTABLE_ADV_INTERVAL to 3000. I was expecting to see...
Greetings,
I am interfacing AT24C01A(EEPROM) with nRF52 ,SDK11,PCA10040.
For writing to the EEPROM and reading data fromn EEPROM, I am using the following code,
I have...
Hi, when reading the BLE Mesh example code, I got really bewildered by this function:
access_model_add
and inside, there is this gem:
element_has_model_id
...
What's the expected behavior when reading a register that is write only? For example, I'm using an some code that is reading the value of the TASK_START register of the RNG...
Will the Bluetooth low energy advertising tutorial run on 2 x nRF52 DK's and not on 1 x nRF52 DK and 1 x nRF51 Dongle? I wish to test the capabilities of BLE 5.0 (not be limited...
Hello
I'm a beginner using NRF51882, I do not have enough money to buy NDK51 Development or NRF Dongle, the solution I changed STLINK STM32 to JLINK by following tutorial...
Hello,
when starting a new project I took the nice Heart-Rate-Example which works fine at my PCA10040. Then I started to add services and characteristics by copying and adapting...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Can the SoftDeivce flash functions ( sd_flash_write specifically ) be used after the SoftDevice has been disabled? If so will the events still be sent to the handler or will...
each time my program start, I get the error m_evt_schedule_func error 4
what's the cause of this error? is it because I spend lot of time on the handler??? the handler...
I am trying to program a nRF52328 present in the Taiyo Yuden EYSHJNZXZ module. I am using Keil v5, nRF sdk v 12.3, soft device 132.
I get the following error when I try...
