GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I have newly purchased the nrf52 Development kit . Does it contains any pre-loaded firmware detectable on the ble scanner or nordic connect device, becasue I cant see any...
Hello,
I would like to use the button handler library (app_button) from the nRF SDK on my nRF52840 to detect pushes on pin P1.05. However, no events are detected when the...
HI experts
I have a nRF51-DK board. I have flashed it with S130 softdevice. I have also flashed it with BLE_APP_HIDS_KEYBOARD application example. I have made little change...
/DfuImpl: Setting object to Command (Op Code = 6, Type = 1)
Something like this printed in log cat and after this app is stuck ..rest of the process not execute..
If the nrf51822 device goes out of range then comes back in range, the application automatically reconnects with the device and tries to read a particular characteristic....
Hi,
We have a set of connected devices in a building of around 22 floors, may be around 6000 devices, can it connected using a nRF52840 Mesh network? Please let me know...
I used the 52810 board, with the SDK14. I modified the 52810 according to the official website related to the relevant definition. I can run the code but it does not print...
I've been searching and wanted to confirm that in SDK13, it's still on us to implement a timeout if a device is placed in DFU mode? As others have said, this just seems such...
Hi,
I am planning to enable autoconnect feature in our app, the same way it is done in nrf-connect app. Is there any way to get the code for nrf-connect app or any other...
Hi there, I was trying out the ADC example which is sampling 10 times the ADC and then generating the event NRF_DRV_ADC_EVT_DONE to process the data.
I extended the handler...
Hi, Im using Nrf51422 DK board.
When I try the ble_app_multilink_central example in the SDK12, it works on the DK board.
But it does not work in NRF51822. (NRF51822 QF AA...
Hello All
I planning make DFU over the air.before going to this experiment i want know some information
Any Soft device is fine or Required specific SD
...
I would like to disable the secure timeout in the bootloader for a specific condition.
I am using nrf52832 chip, sdk 12.2, softdevice s132 v3.0.0 with secure bootloader...
Is possible to use DMA to communicate with nRF24l01 on STM32?
In my test, when Master spi CPOL = 0 and CPHA=0, it can communicate with nRF24l01 by SPI but not accessable...
When plugging the PCA10028 into my PC, LD5 is permanently turned on (or blinking to fast to see it).
But if plug the board into at power outlet, LD5 starts blinking rapidly...
