Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
How can one calculate the distance between two beacon based on RSSI values?
How can one find location based on RSSi values of the beacons ?
What are short comings...
I tried the Bjørn's code : devzone.nordicsemi.com/.../
I didn't make it... Could you help with a simple code you've tried for adxl345 ?
Thank you
Yassine
Hi Nordic!
On the radio_test example, the functions scanf and printf are heavily used, however, I haven't found where they are defined. This example is reading the data...
I really need your help regarding a problem. I developed my own pcb with nrf52 and verified it with your hw engineer. I just finished soldering and hooked it up with your...
Hi,
Is there any ready made app of NRF52 and NRF51 ( beacons), where beacons are communicating with the NRF52 and based on some nordic app for PC we can view that how many...
I have created a BLE peripheral device using nrf51822. I have used sdk12.0.0 with soft device 130 and I am using NRF connect mobile app to test my device.
When I connect...
Can I create Characteristic with Notification only, no Read, no Write
I can remove the //char_md.char_props.write = 1;
and only the Read and Notify Properties show up...
Hi,
I am totally new to NRF52832 chip and I want to use ANT+ in my sensor networks related project. I am using keil compiler and S332 softdevice (I am also using BLE therefore...
Hi,
I am working for the first time with NRF52832 flash data write. I have (ANT + BLE) application and and I basically want to save the data in ROM in order to keep it saved...
Designing a custom pcb, we have a few questions, and maybe you could help a little bit.
On this Nordic design ,before proceeding to layouts :
Can I skip pins 45/46...
So im trying to create a generic library to test any Bluetooth device. So far i can connect to the device but since i dont know what are the services and UUID available im...
Tried Flasher Portable Stand-Alone Mode with J-Flash 6.14 as following:
Create .jflash Project for nRF51822-QFAA
Open Data .Hex File
From J-Flash, select Target...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
