Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,
I'm currently developing an application on nrf52832 that'll use SAADC low power to fetch battery voltage level and report that value on BLE advertising data. I've...
I am trying to use NRF51822 GPIO to generate a pulse with max width of 0.3us. According to other tickets in the forum and the product spec, NRF51822 should be able to generate...
I am using a nrf52 dev kit as well as a raspberry pi to set up the cloud coap example in the nordic docs. I have set up a 6-4 tunnel through hurricane electric and have full...
Hello,
I'm playing beep sound using pwm1 (timer1).
The onSound() starts beep sound.
The disableBuzzer() terminates pwm1.
The handler_buzzer() selects continuous...
Hi,
I'm using nrf51822 and ble_app_uart in SDK12.3.
Testing with android app nRF UART v2.0
I have some problem with BLE connection.
First, Sometimes when I tried...
Dear Nordic:
I have transplanted my code from sdk 10.0(nrf51422+S310) to sdk 13.1(nrf52832 + s332(v4.0.2)).
I program softdevice and application to my board by nRFgo_Studio...
I just tried to add a custom service, so I expanded my ble_cfg.gatts_cfg.attr_tab_size.attr_tab_size. Now, when I call sd_ble_cfg_set(BLE_GATTS_CFG_ATTR_TAB_SIZE, &ble_cfg...
Hi everyone,
For my project I'm currently using the sdk 10.0.0 (S310 on a nRF51422) and I would like to use the Secure DFU provide by the sdk 12.0.x.
Working on a nRF51422...
Hi everyone
We have a custom made board with NRF52832 chip. We are send it to FCC test lab and they told us the occupied bandwidth (OBW) is too small, 940kHz less than...
Hello,
has anyone tried new v1.1.0 for nRF6707? If I change the window size to more than original 2.0s, GUI becomes very laggy and it is very hard to stop the recording ...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
