I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Error executing NovelBits Gateway app on nRF52840 with SEGGER Embedded Studio. "Cannot connect to J-Link via USB" Running the SES for ARM 3.40 on Ubuntu 16.04 64 bit. The...
Hi,
We want to send our pre-production ready product for compliance testing. Selected testing laboratory told us " Conducted sampls should be set in continuous transmit...
Dear All,
so we have an embedded SoM running OpenWRT and I was wondering if I can make use of nrfutil even if not connecting a nRF52 via USB but via UART.
What I want...
So as far as I can make out, when I load a new application into the flash, the NRF52 will attempt to first load a secondary memory space and if successful, it will then replace...
Hi,
Right now i am using Blinky example in Peripheral section of SDK15 (S140). I would like to enable Coded PHY (BLE_GAP_PHY_CODED) instead of default setting (BLE_GAP_PHY_1MBPS...
Hi, I have problem with timer in nrf52810. My TIMER2 counts very slow. I declared it as NRF_DRV_TIMER_INSTANCE(2); and config struct is:
.frequency = NRF_TIMER_FREQ_16MHz...
Hi ,
I can compile and use the UART example but when I try to use it in my project I get some linking errors
I have copied and past all the sdk_config.h file to my project...
I am waiting for my custom pcb based on the nrf52832 to be ready and I want to test the flashing process. Is it possible to program a nrf52 DK with another nrf52 DK using...
Hello,
I was wondering if there is some way to program a device to act like a BLE slave, which would sleep and periodically wake up to stay in receive mode for a certain...
Hello, I'm confused what the NRF51422 uses for it's digital IO reference. So for example, If I use a 3.0V coin cell battery through its DC/DC converter: 1. What voltage does...
I download the SDK at https://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK/nRF5-SDK-zip/59011 . When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c...
Hi,
I am using SDK10---->ble_app_uart--->pca10028--->s110 for non-invasive GLUCOSE measurement. I checked nrf_adc.h file & used adc_sample = nrf_adc_result_get(); for getting...
I am using nrf52832 development kit and softdevice v5.0.
I am using this code which I have attached.
I have added all require files.it might be not showing to you because...
My current setup is this:
I have a nRF51822 beacon (tiny coin cell beacon) advertising with its default settings. I have another board, a nRF51822 Development Kit, that...
