Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
When initializing a UART instance (0 or 1 or both together), the current consumption increases to 600 μA
Then deinitialized UART, but consumption is not reduced!
- I tried...
Hello everyone!
I've had an ESB application running o the nRF52832 for more than a year. When I moved it onto the nRF52840 it no longer works. There are no changes to the...
Hello,
I'm developing a home automation related product using mesh. For testing mesh functionality I'm placing the DK in different rooms and testing the range. As a power...
I have a small project on a custom board using an nRF51824 processor.
The code basically initializes the BLE stack timer and GPIO and then falls into a loop
while (true...
Hi everyone, There were already a few people asking about similar problem, but none of the suggested solutions worked for me so far.
I am trying to communicate nRF24L01...
Hi,
We are developing the BLE project by using nRF52832 module.
This project we had started to develop on SDK v14.1 and it worked perfectly. But then we have migrated...
Hi I'm a bit confused about how to get two clints on the same mesh network and can you have more clients on the same network. If yes, is there someone who has an example or...
Hello
I want to create Bluetooth mesh network and I need that each of network nodes turn on/off selected time (including provisioner). Can I use only nrf_mesh_enable/nrf_mesh_disable...
