Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
Hello folks.
Easy question.
I want to add a .a static library to Segger Studio, but I don't know exactly where to add it. I know how to do in a Makefile with GCC, same...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
Hi everyone, I am newcommer in here. I just buy one nRF52840 Dongle. I want to connect it with nRF52832 DK with ble_app_uart implemented; and open a COM port in MATLAB to...
Hi,
My application is based of ble_freertos_hrs example (SDK 14.2, nRF52832) and I need some variables to survive an assertion.
It appears that Keil has deprecated #pragma...
Hi Engineer： When I use nrf5_SDK_for_Mesh_v2.1 to debug the "light_switch" project, I always need to use a minimum of three boards (one as a provisioner, one as a client,...
I am using the nrf52832dk,i am working with the spi example for the sdk15,which pins are used for the spi protocol. I am enabling spim0.in sdk_config. h the pins number 3...
I am using NRF52832 as tags for asset tracking. I want to sense whether the asset is in movement or not as simple logical '0' or '1' response from sensor. Please suggest a...
I need sample code for the multiceiver mode. I want to send data from multiple NRF24LE1s as transmitter (to be exact 3 in number) to a single receiver. I read from the data...
