Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Please tell me how to change the communication data length of BLE communication to 244 bytes and shorten communication cycle. Thank you.
I am using the version of [nRF5_SDK_15...
I know that there is a similar question here but the problem that the question is pointing on is not solved. Even in one of the answers is mentioned:
Now I found that...
When I run the example "ble_app_hrs_rscs_relay_pca10056_s140" on the development kit while debugging, then the SVC call for enabling the softdevice will stop at Address x8C4...
Hi! I want to implement at BLE switch(PTM215B) to a nRF52 DK, The switch sends advertise messages with switch status data. So i want to create a simple central that scans...
nrf52832 code always block at nrf_spi_event_check, my application include a app timer 200s period, after timeout, drive spi to get a RF sensor for sending some data, and also...
I am working with the nRF52832, SDK14.0.0. I want to perform a flash write on a watchdog reset to save the current state. However, the watchdog resets after two cycles of...
I've used the 'secure_bootloader' project, updated with the public key, to flash on the DK. The project 'ble_app_buttonless_dfu' built and packaged as zip can be DFU'd with...
Is it possible to _send_ multiple packets per connection interval, using the pc_ble_driver (and a nRF52 or nRF51 DK) in BLE CENTRAL role?
I found some answers on the devzone...
Hi, I developed a static library including drivers for spi, twi, gpio, adc and few others. Now when I create application and link my library it works ok as long as I am using...
Hoping to get some help. Using swift3 and xcode 9.3.
I can write data from iPhone back to nrf52 peripheral fine if it is a Dbl.
When I try to write a UInt16, it crashes...
I plan on using the nRF51 Dongle meandered antenna for a design involving the nRF52810. Since the nRF52810 has an internal balun, does that mean that L1, L2, C5, C4, L3 and...
hi,
i have a custom board with nrf52832 as it's core. i want to program with st-link v2 programmer.
i am using sdk 14.2 and soft device s132 v5.0. on target location we...
Hi guys,
We have tested the mesh range in the nRF52840 chip (max tx power) in LOS and we got more than 200m.
W're planning to use the mesh network inside hangar with a...
