Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I've used the DFU bootloader from SDK 14, s132 and the ble app uart example as a boilerplate for my app.
Now i'm looking into making some relatively large changes to the...
Hi,
I have problem compiling "HTTP application update" sample form the SDK for the NRF9160. I am using all the latest tools: * segger embedded studio: v4.18 * nrf SDK v1...
Hello,
I had problems connecting the periphery to the central. When I connect them, I get notifications like this from peripheral, but after this message they don't lose...
Hi,
We are using nrf52 dev boards running mynewt and until two days ago we could use the app to identify/provision and get composition data for nodes and get composition...
We are in the final throws of testing our boards that are based on the BLE UART Peripheral application. The current test environment involves monitoring board and battery...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
Today ,I look up the SDK revisions，found that SoftDevice S130 V2.0.0 support NRF51822 V3.Now my production use S130 V1.0.0,but Chip revision unknow(N51822 QFACA2 1921DC).Is...
I have an application based on ble_app_hrs_freertos from SDK14.
Sometimes the application will not start advertising. When this happens, it does not help to power-cycle device...
Hello, I start in programming on nrf9160 DK. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hello,
Good Day!!
My question regarding the reset functionality of the device.
Reset the device on the short press of the reset button and on Long press (for example...
Requirements:
Transmit an advertising packet that can be received by a native IOS App & a native Android App.
Using an nRF52810, I need to set it to Advertising (non-con...
hi,
The data is sent to the app by sd_ble_gatts_hvx(), but the data obtained by this app is wrong.
When salve sends a byte, the data obtained by the app is always 0,but...
