Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
Does the zephyr stack support scanning for extended advertising packets on the nRF9160?
I tried opening the lte_ble_gateway example in ncs v.1.1.0 and adding CONFIG_BT_CTLR_ADV_EXT...
Hi,
Nordic Part Used in Design: nRF52810
SDK version used 16.0.0.
We found for nRF52810 it supports peripheral mode as well as bootloader. I didn't find any example...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
sd_ble_gap_adv_set_configure() is returning error code 7 when I use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
OVERRUN error occurs when receiving UART.
I'm using EasyDMA with UART and want to increase the EasyDMA reception size. Which settings can be used to increase the reception...
Hi,
I have NRF52833 DK and using nRF5 16 SDK on KEIL IDE.
I am trying to compile blinky example from the peripheral and it is giving me this error
Error #541: 'NordicSemiconductor...
During production we need to provision each device with some custom data that must last the life time of the device, ideally using nrfjprog. What is the best way to do this...
There are several use cases where we want a bonded peripheral to indicate the service changed characteristic to the central.
The main case is when developping and adding...
hello can someone help me solve this issue. i am not being able to controll this led . if i send any number the led will always turn on
Regards
static void led_col_write_handler...
Hello,
I want to test the range of Adafruit nRF52840 express feather(BLE 5.0) board. I did the setup on arduino IDE. My question is can I perform the long range test of...
Hi, we have a project that we're currently working on, and we're looking for some information on BLE behaviour that would be very helpful. We are currently using SDK 15.3...
I'm trying to build aws-fota program following this instruction, but get an error https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/aws_fota...
I have a nRF52840 dongle.
My understanding is that the nRF52840 has an on-chip regulator (Vdd out) that can be set from 1.8 to 3.3V.
So it's recommended to use a debugger...
Hi
I am attempting to add nrf_crypto functionality to the example uart ble peripheral project via SEGGER Embedded Studio on MacOS.
I have opened the project options and...
I have two devices, one is a beacon (DEVICE #1) and the other (DEVICE #2) collects information from the beacon. I'm advertising with a transmit power of 4dBm. I want to reduce...
I have previously had success with programming the nRF51 Series using the nRF51 DK and want to use the nRF52840 DK to program a nRF52840 that will be run in High Voltage Mode...
