Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
How to flash SoftDevice and Bootloader (OTA enabled) to nrf51822 by CMSIS-DAP programmer?
For instance: I did cmsis-dap programmer with mbed code form github.
Can I do that...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
I know this was asked before, but none of the posts address my problem. There is a similar thread , but the issue on that one was that the softdevice was not being used. I...
Hi all,
I'm implementing a Bootloader with the source code provided no the website (Windows C# app, nRF24LU1 station app and nRF24LE1 device bootloader/app). Everything...
Hello,
When using the nRF Master Control Panel I see other Beacons with "Complete Local Name"... I am building an iBeacon but have not found a way to set the name and have...
The following thread talks about CPU unblocking during connection intervals.
devzone.nordicsemi.com/.../
How does this feature affect BLE Radio Notification? Do...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
Hi....
We are working on PCA10028 DK with S130 softdevice version 0.9.0 alpha. Could you tell me about the release of stable SD S130. Hope it will be soon.
