We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Story and Official Code Test Passed
I am trying to integrate BLE into Smart-Lock and LoRa Terminal . So I build a custom board with off-the-thelf modules to evalute and...
I am current develop a "Surface Dial" hardware compatible device. (nRF51/S110)
Everything is ok but the host PC will freeze about 30 secs after my device wake-up from sleep...
I'm working on a product that is somehow related to geolocation. As part of it, RSSI measurement is sent back at high frequency to the central. Currently based on nRF51822...
Newbie here hoping to get some direction on how to properly setup a timer to have a timestamp displayed for DEBUG messages. I am working on a PCA10040 board. I tried looking...
Hi,
I have some basic doubts in installing the power profile on nrf52Dk(nrf52840). I'm trying to use it on my central device which has its application FW running. I have...
what is the sending data rate of the sd_ble_gatts_hvx() ,why i use sd_ble_gatts_hvx() send data 600Byte per second, it lost data again . it can be use yes or no ?????????...
I can copy a Hex file from a Mac to the mbed USB drive and the code executes correctly. However, if I upload the hex file from any windows PC in our office (Windows 10) the...
Hello, I am trying to generate pulses with the nRF52832 chip.I created a basic setup for test purposes; I simply connected a LED to the PWM output, but even though I put 0...
Hi,
I have designed the Circuit using NRF52832 BLE and AT8010-E2R9HAA RF ANTENNA and tuned the circuit accordingly. Since the antenna was not available so I placed other...
I'm relatively new to development on the nRF52832 and I'm trying to find information on how to use the sleep mode with the SAADC.
Goal: The micro should be in sleep mode...
Hi,
I am trying to create a BLE node which can perform dual role(advertising/scanning) to create mesh of multiple nodes. I am planning to do it with the help of timer....
the project has a problem with DMA,the detail is:
on the board,NRF52832 and extern chip communication with i2c bus,the chip through a pulse wake up nrf52832,NRF52832 start...
I have NRF51822 Controller(custom board,S110) used to send some sensor data. i can able to receive data in android and ios. now i want to communicate to Laptop which has internal...
Hello Everyone,
I am new to nrf51822 (using S130). I made some custom service that accepts float numbers.
This might be noob question: I want to send float values from...
