Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...
i want to communicate nrf52dk with arduino over spi.i want use nrf52dk as a master and ardunio as a slave.kindly refer me some example or code or any thing which s helpful...
Hi,
I'm working on migration from project based on SDK12.1.0, 132SD3.0.0 (calling A project) to the one based on SDK13.0.0, 132SD4.0.2 (calling B project).
I developed...
hello,
Please let me know why the BLE_GAP_EVT_DISCONNECTED event does not occur even when I exit the application.
It does not always occur when BT smart setting is enabled...
case 1: i use rtthread RTOS, main() disable global irq，on os scheduler enable global irq.
but i on task init stack, sd_softdevice_enable not return,system always reset.
...
The Device Family Pack 8.12 needed for the newly released
SDK 13.0.0 and SD S132 4.0.2 is missing from the download area.
Error #544: Required Software Pack 'NordicSemiconductor...
Hi everybody:
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
My last post showed that if BSP_SIMPLE is defined, I can't use button event trigger function...
Considering my use case, the size a certain characteristic is dynamic, and the notification should only contains the exact amount of data, even though locally there should...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
Hi Nordic guys,
we are observing a strange behavior. Here some background on the project:
we are developing a peripheral device that asks via L2CAP signalling connection...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
