Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi
The j-link detects the chip, but for not obvious reason the j-link and keil will trough an error when I want to program the chip, here is the j-link out put. do you have...
Dear All,
I would like to order Li-Po batteries for my nRF52840 development kits and need some information. From the battery, what type of female battery connector is needed...
Hi, I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi,
By mistake, I clicked 'fill with zero' button in Jflash, may I ask, is my chip bricked because of this? Thanks.
The following lists my steps:
program the...
Hi,
I'm trying to use the SysTick timer on nRF52 to time some various tasks for debugging. I configured it like so, which I expected would cause SysTick_Handler to be called...
I didn't find any documentation in the peer manager for the need of this write buffers.
I do understand, that peer device data is stored there before written to flash. But...
Dear Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210 v5.0.0
I have 3 devices: two masters (No. 1 and 2) and one slave (No. 3). In my application, I pair the...
Hi guys
I have one nrf 51822 demo board.
And I want to buy one more board as BLE sniffer.
Can I use a nrf52832 demo board as sniffer to grab packet between phone...
Hi guys
I am programming nrf51822 demo board with sdk11 and try to finish service tutorials .
I finish all step in service tutorials and try to get service information...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
