I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I have been able to get all the MPU based projects to work from this Github site (which has been very helpful!) with the exception of this one.
The accelerometer values...
For a device that has APPROTECT enabled, it is required to use nrfjprog --recover to re-enable access.
What is the mechanism that nrfjprog uses to perform the --recover...
With the nRF52, is the RTT functional when APPROTECT is enabled?
I would expect not since the RTT relies on memory accesses which should be disabled with APPROTECT
Hi,
In SDK11, it was possible to call app_sched_execute() from a function that was itself called from the scheduler:
void app_sched_execute(void)
{
void * p_event_data;...
If you dont have an external 32Khz crystal for the nRF52832, besides the higher power consumption, are there any other issues ? e.g. CPU starvation affecting my app during...
Hi all,
I work with a nrf52, my project send and receive Beacon data.
when i work only with 2 card all works fine but when there are several transmitter and 1 receiver...
I've got an nRF52 application which is based on the nRF OpenMesh github.com/.../ but has been vastly customised. The application either acts as a mesh device and allows a...
As the title，I recently want to use nRF51822 to communicate with SmartCard in ISO7816 interface. but I don't know how to do this.Can anyone share the example code online ...
Hello,
I am using the nrf sniffer from adafruit to pick up ble packets from my NRF52. Everything has been working fine for the past 3-4 months. Yesterday I wanted to test...
I'm trying to create a HID over GATT device that is not a keyboard, nor a mouse. About a week ago, I came close by being able to read some data in an OSX app from the device...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
