Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hi,
I'm trying to get the actual connection interval used between my nRF51822 device and iOS device.
I have read this article , but I cannot get it worked.
I used sd_ble_gap_ppcp_get...
Hi,
I want to disable the softdevice (S110) in order to use the "flash_page_erase" and "flash_word_write" functions. But, when the sd_softdevice_disable() is called I get...
Hidden in the guts of this answer is:
Please be noted that not all central
stack have full support to
automatically discovery secondary
services (e.g S120 stack)...
In the code for the bootloader in dfu_dual_bank.c and the function dfu_init , I currently get an error code on timer start: 4 ( NRF_ERROR_NO_MEM ).
err_code = app_timer_start...
The device name is set in the usual way at the start of gap_params_init():
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,...
Hello,
I am new to BLE profile development. I searched in web but could not find out a useful guide for this in terms of actual implementation(coding). It is seen that all...
Why is the "old" EK "not recommended for new designs"? Will the old EK work with the IOT SDK?
(Maybe it is chip rev dependent? I don't have the my EK on hand so I don't...
Hello,
I have purchased a Intel Galileo Gen2 (x86 Arduino) and RedBear BLE shield v2.0. The Arduino IDE I use is Intel's version. I have imported the corresponding libraries...
The application uses bsp_button_is_pressed() but this device has no buttons. This results in err_code set to NRF_ERROR_INVALID_PARAM and subsequently a system reset during...
As previously reported for SDK 7.0.1 here , the documentation for SDK 7.1.0 in:
API Reference/nRF51 SDK/Peripheral Drivers/GPIO and GPIOTE
is missing all info about...
I can't find documentation for the HAL functions in the latest 7.0.1 SDK
Specifically the functions in nrf_gpiote.h
C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Drivers...
Hi,
We are in the process of creating our 2nd pass boards with following components to achieve good RF range>20 meters.
JOHANSON 2450BM14E0003 and SMD Chip Antenna 2450AT18B100...
I have met a problem in communicating with nrf8001.
After reset nrf8001, RDYN is low which means it has something to send. Then I pull low of REQN and start receiving data...
Hi,Nordic:
I use an STM32 to communication with nRF51822 through SPI, and i set the STM32 to master,the nRF51822 to SPI slave, 51822 works as SPIS.
When STM32 send a...
