Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am considering using two nRF52832 or nRF51822 's for a project which requires two way BLE communication. Pressing a button on one end should cause an event on the other...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
Hi All,
I have a general question about the FreeRTOS implementation for SDK 14.0.0.
I've added FreeRTOS onto a basic UART BLE peripheral example that I wrote. I referenced...
Hey Guys,
I'm trying to import an existing Keil project into Segger Embedded, SDK 12.3.0.
I know this link exists which explains importing prior to SDK 14.2.0. However...
In the PS v1.4 pages 13-15 related to the QFN package.
Pins 11, 12 (P0.09, P0.10) are marked with the note '1'.
On page 15, at the bottom, the notes are enumerated:
...
I have a button that will put my device into pairing mode. While in this mode, I want central devices that connect to form bonds so that when not in pairing mode I have a...
Here I document how, in Eclipse, to start two, concurrent debugging sessions to two NRF5DK boards (or other debugging probes) , connected to different USB ports of the same...
Hello everybody,
I have problems with selectivity when I scan. There are 5 peripheral devices with different " DEVICE_NAME " but the same UUID and type (same " ble_uuid_t...
Hi, I am working on a custom board of NRF 51822 driving multiple leds from pin 21 to 30. I am trying to get and transmit the status of all the pins with help of bsp functions...
Hi,
We'd like to implement a feature that allows changing a BLE connection from [central device #1 -> peripheral] to [central device #2 -> same peripheral] (similar to Apple...
Dear friends,
The nRF Connect BLE app is connected with a local device acted as Master. The app supports the configuration of the local device's GATT attribute table, and...
Hello,
After i uploaded a program on my nRF52832 i couldn't enter debug or reprogram the chip. This is the error i get when trying to erase the chip using Segger J-Flash...
Hi,
I am using peer manager to use static passkey with nrf51822, sdk11 and s130 v2.
Is the "case PM_EVT_CONN_SEC_START:" the best place to put sd_ble_gap_tx_power_set...
