In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hi,
I want to use ble_app_multilink_central example for my own application. Here are my problems:
Setting MIN and MAX CONN_INTERVAL to more-less 20ms or lower (both...
Hi.
In my program I need a frequency at 2 MHz (a square wave with duty cycle at 50%), it should just run a frequency in a short time, under one second. Also the code must...
Hi,
I'm using a simple timer with interval set using "APP_TIMER_TICKS(1.4, APP_TIMER_PRESCALER)" alongside softdevice. Now i'm trying to get it to go faster but it would...
I got this error when programming the Development Dongle. The dongle is recognized in the
Master Control Panel as a COM4 - xxxx, and when is connected a green led and blue...
Hello,
We are French students in a school of engineers. We are developing a project based on the nrf51822.
Actually, we implemented RIOT OS on this SoC and we would...
I am currently using softdevice 8.0.0.
I am curious if the nRF51822 will be upgradable to be 4.2 compliant with a new softdevice release in the future? My understanding...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am trying to allow 2 peripherals to bond to a central, and would like to be able to use 2 push buttons to delete the bond information for either device. Is it possible to...
Hello, Nordics :)
I am trying to develop ANCS device with SDK 8.1, but I have some problem.
This are my environments.
Board: custom board.
chip: nrf51822AA...
Hi,
Function call to > err_code = ble_advdata_set(&advdata, NULL);
returns always err_code = 7 (NRF_ERROR_INVALID_PARAMETER) for a 128 bit UUID type (BLE_UUID_TYPE_VENDOR_BEGIN...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
I'm seeing the resetreas show the CPU lock-up detected after I reboot. This error is occurring while using the ADC. What type of fault condition can cause a CPU lock-up detection...
Hey everyone,
I'm developing an application using the IoT SDK . The first part of the application consisted of a normal BLE peripheral to interact with an android app....
