Hi,
I’m developing a speed sensor and cadence sensor that support both BLE and ANT+ peripheral connections. I plan to use the nRF52805 with the S312 SoftDevice and nRF5_SDK_17...
Hello Nordic team,
I'm working with the nRF54L15 DK and using the latest NCS version that supports Bluetooth Channel Sounding. Here the sample is channel_sounding_ras_initiator...
I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
We are looking at using the Gazell protocol for a project. There isn't much information out there except for the "Gazell Link Layer User's Guide"
developer.nordicsemi.com...
Hi,
I've been working with a two LPC1768 boards with connections to Addicore nRF24L01+ boards.
I have not been able to successfully receive an ack on the PTX board although...
Hello
What is a typical current draw when using a PORT GPIOTE interrupt? I seem to be drawing approximately 200uA with a port event enabled. Is this normal?
I'm using...
Here: developer.nordicsemi.com/.../a00050.html
"The Bootloader/DFU with SoftDevice update example shows how a SoftDevice, bootloader, and pplication (sic) can be updated...
Hi,
I am trying to bring up custom board with 51822 CFAC-A0.
And I am continuously getting the following error as soon as the code does advertising_start().
I am using...
This comment for this line of code in twi_sw_master.c is misleading:
#define TWI_DELAY() nrf_delay_us(4) /*!< Time to wait when pin states are changed. For fast-mode the...
Hello all
I'm new to Nordic products and the Keil compiler and in order to fast-track my development I have two computers, home and work, running Keil MDK-ARM (lite) with...
As said on the topic "GAP Address types", the random static address can be changed when system boots up. I can't find any content about how to make it. Could anyone offer...
Hello,
I have a problem with getting i2c to work. What I did is enabled the 2-wire block, and tried to send various data as a master(by setting the registers), but I cant...
Hi Nordics.
I want to change SDK version of my project from SDK 6 to SDK 8.1
(actually I am trying to restart my project with new SDK 8.1)
My project base on the ancs...
