hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Good morning,
Is it planned to raise a new version of this application note but based on the new version of the SoftDevice? If yes, when is it expected?
Best regards...
Where could I find the software for the Connectivity chip(ATSAM 3U2C) that enable the mbed connection?
If I flash the EK board with this software, could I use EK(evaluation...
Prior question: nrf51422-soft-device-options
As a follow up to my previous question, has Nordic developed a stable boot loader to use with the S110 soft device and the...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi guys,
I can get a rand number use the API:err_code = sd_rand_application_vector_get(buf, bytes_available); but the question is that How can I get a rand number just...
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a strange problem with pstorage function with nrf51822 with s110 v6.
I need to use nrf_delay ( about 1 second long ) after store and before read.
This is the source...
Hi,
I am using softdevice 6.0.0 and ble_app_hrs example in keil on a custom nRF51822 board. Compilation goes fine but when I try to debug I notice that the firmware seems...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
