Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi All,
I am novice in this nordic nrf 51822 programming. I wanted to know the best way to do the
following.
I have two different functionalities to be run on eval...
Hi All,
In ble_app_hrs example two function is defined for gpiote_init()
1)
static void gpiote_init(void)
{
APP_GPIOTE_INIT(APP_GPIOTE_MAX_USERS);
}
2)
static void...
Hi
I found there is bonding managing routine in SDK HRM and Proximity examples.
bond_manager_init();
It means in these two case, after pairing with BTLE host, the...
My question is regarding the PPI channel groups. The documentation is extremely limited and leaves many questions.
My goal is to generate 3 PWM signals from a timer with...
If i understand tasks are for outputs and events are for inputs.
Wanted to know relationship between channel and the pin numbers. do they hold the relationship like...
Hello,
I am really confused on how to get a custom BLE service up and running. I have read through nAN-36, and compared the suggestions in that document to the HRS example...
In nRF51 reference manual v2.1 section 18.1.1, it mentioned that the RTC must be able to
run while the 16 MHz system clock (SysClk) source is OFF. 2 questions :
Q1: Since...
Hello,
I'm trying to get the SDK examples working in Eclipse. I have followed all steps(except debugging part) in the nan-29, but i can only import the s110/ble_hrs example...
I am looking for the spacing in mils or mm between the two samtec connectors on the nrfGO board. I am making my board to interface with the PCA10005/PCA10004 and I would like...
Hi,
I'm new to nRF8001 SDK and Bluetooth and I hope my questions are not too stupid lol. So here it goes:
I'm using the Nordic nRF8001 SDK to implement a self-defined...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
