Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi,
When I build the zephyr/samples/hello_world program for the nrf5340dk_nrf5340_cpuapp target it works as expected, but with the nrf5340dk_nrf5340_cpuappns target I...
IDE: SEGGER Embedded Studio for ARM 5.32 SDK: nRF5 SDK 15.0.0 and nRF5 SDK for Mesh 2.1.1 demo: examples\sdk_coexist\ble_app_uart_coexist\pca10040\s132\ses\client_pca10040_s132...
I am using NRF52 DK board and removed SB9 track to connect my ammeter for current measurement . I have taken ble_app_blinky ( peripheral example ) from SDK15.3.0 .
My application...
hi,all
I'm using nRF52833, s140.. pca10100.
I want to read my pcb's touch gpio..
If I touch it, it falls down to low. ( I checked it with scope..)
When viewed through...
I'm testing USB audio demo. I changed bit resolution of APP_USBD_AUDIO_FORMAT_DESCRIPTOR 16 to 24 but the widows10's USB audio device is still 16 bit. how can i do that?
Hi!
I'm trying to pass the BLE data to the PC using nrf52840 DK.
To do so, I've started with the ble_app_uart example and it was able to build fundamental features–find...
Hello,
our application requires to emulate keyboard, e.g. to write strings like "hello world\n" as it might be typed by the keyboard. According to the recommendations...
Hey I am using nRF 52840 DK
I am reading temperature from Segger code and displaying it in the log
But I want to display that value in my android nRF Mesh Application...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
I created a 500ms timer to send mouse movement as follows.
m_mouse_movement_send(5,0);
When the device runs there, the device will restart. The error code is NRF_ERROR_FORBIDDEN...
Hi engineers,
I want to use the pin P1.09(NRF_GPIO_PIN_MAP(1, 9)) as GPIO, but when I initiate it, it seems fail.
I've looked through the relevant issues here, but got...
Hi,
I am currently trying to build a project using a nRD9160 with legacy code and am receiving this error when trying to load an existing project:
I understand...
I am not able to successfully use your nRF UART app to communicate with your nRF52840 DK. I get a warning when installing the app that it may be too old for my version of...
I'm still learning BLE development so I apologize if this is a basic question.
Here is a screenshot of a recent capture I did with the nRF52-DK. The bluetooth sniffer is...
Pardon my ignorance of the nuances of Security and Encryption but what I am observing is a bit perplexing.
Every time I run the nrfutil command to generate the bootloader...
