Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi,
I'm starting to work on nRF52 with eclipse (on Ubuntu). I use this tutorial to configure everything : devzone.nordicsemi.com/.../
Everything looks good but when I try...
Hello,
I am having difficulty having two nRF24L01P's communicate with one another.
I have set up the devices in what I thought was a minimal system.
I will appreciate...
What is the switching frequency of the DC/DC regulator in the nRF52832? The DC/DC is great for reducing power consumption, but I am worried about the switching noise getting...
Hello.
I am trying to save i/o lines on an 8-pin PIC, and planning to run an nRF24L01P with its CE pin tied to VDD. I am willing to power-down to get out of the RX mode...
Hi
I am using an Identive NFC reader/writer SCL3711 and their sample app to read tags.
In the sample app, through the debugger I can see that it is registering an NDEF...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use nrf51422 and integrated BMA250E for Pedometer,
Now I can count the step but I dont how to calculate the speed, cadence and stride length like below
static void...
Hi All,
From my firmware I need to send large ble packets say of 1 K to the phone.
Is there any library or example code for sending large packets. Currently I am splitting...
Hi,
Our application requires that we connect a nRF52832 to a Microchip PIC32MZ host via the Nordic parts UART (RS-232 at CMOS levels).
In a previous application, we...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
