After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi All!
I moving from SDK 14 to SDK15 and faced with another errors:
after sd_ble_gap_scan_start(..) call, the BLE_GAP_EVT_ADV_REPORT message is occurred (once), then...
I used nRF5_SDK_14.1.0_1dda907.
I used fatfs example.
Wirted data in the same file to sd card.
I discoverd that Max size of the file is 16KB.
Over the max size of...
Are there any plans to include CMSIS-NN libraries in the SDK?
If so when?
If not, what build flags should I use to get the fastest runtime?
Thanks,
Quinn
how can I store outputs sent from JLINK SEGGER_RTT to a file?
how can I send data on RTT channel 1, is there any instruction for that?
/** loop */
sprintf (buffer,...
I'm trying to adapt the DFU bootloader to work with a SPI slave as the transfer mechanism, but I'm running into issues getting the SPI communication up and running. I've added...
I'm trying to load ble_app_hrs_c on the nrf51dk and im getting the error
"error: L6047U: The size of this image (34328 bytes) exceeds the maximum allowed for this version...
Hi,
I am trying to receive BLE advertisements on Ch38 (=2426MHz) without using SoftDevice, i.e. with direct register access. However "EVENTS_DISABLED" is very rarely called...
Nrf52832 based on sdk14.2 development as a slave, when linked with the iPhone, pairing and binding, and then get ancs service; and Android phone connection, direct communication...
I am working on a project working with remote connectable beacons. One of the easiest ways to save power in these applications is to reduce advertising speed, however, this...
Can anyone give me a tip on porting the code below, which works great in sdk12, to sdk14? I'm using the nrf52832 and the ble_app_hids_keyboard example and need to get a real...
Hi, I'm kind of a newbie, haven't had much experience with embedded outside of arduinos etc.
So I started to look at this: https://learn.sparkfun.com/tutorials/nrf52832...
for sdk15.0, SES,
is the twi_scanner example known to work with nrf52810?
getting errors,
undefined reference to nrfx_twim_init, nrfx_twim_enable, nrfx_twim_xfer
Hi,
I am studying the GPIOTE example from SDK 14. I did some modification adding other led and doing the leds blinking in differents times (LED1 blink each 1 sec and LED2...
Hi,
The nRF52832 does not support Long Range and i was wondering if the use of "RADIO_MODE_NRF_250KBIT" would increase the range. My application is a mesh network.
Do...
Hello Everyone,
I am using nrf51822 with S130.
Currently I am using arduino following this repo to program nrf51822 and its working fine. However, I want to shift to keil...
