Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
Hi, I wrote the firmware in SDK 11 preview, and when migrating it to SDK 11 the NFC code does not work, also it seems when the NFC startup code is executed none of the GPIO...
Hi All,
I've not enough experience in nrf51822. I'm developing a battery powered device using the Nordic nrf51822 pca10028. I want to connect two nrf51822 pca10028 boards...
I would like to use the latest ARM Compiler Version 6 ( armclang ) because I need some features of the C++11 language.
Is it possible to use the latest ARM Compiler Version...
Hi all,
I am using keil uVision 5 and nRFgo studio version 1.21.
I am trying to flash softdevice and application in nRF52832, but my device(nrf52-DK) is not getting connected...
I'm having some trouble getting interrupt from RTC1. I'm initialising as follows.
I have an interrupt function as follows.
I'm using the gcc_startup-script. We're...
I have Zephyr stack for BLE hci_uart without any error it got compiled in nordic controller part, but i like to use zephyr stack in host without linux OS. Is it possible to...
Hi,
If I do a directed advertising (peripheral device) with specific peer address, then will the peripheral device visible to other phones ( whose peer address does not...
I have tried out the Running Speed and Cadence Application of SDK 15.1 with the new DK "PCA 10056" (1.0.0, 2018.19, 683681562). We used the Samsung S8 and S9 with Android...
