Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ). The authors demonstrate a remote, passive...
Is it possible to setup a mesh network over BLE and use 6LowPan to enable the use of the IPV6 address space?
The goal is to setup a network without using a star topology...
In order to change the bitrate of the nRF52840 I tried to change the following code on advertiser.c :
static inline void set_default_broadcast_configuration(broadcast_t...
I programmed a PCA10001 with the HID Keyboard example and changed the preprocessor code from NRF6310 to PCA10001. The functions were tested according to the online HID Keyboard...
In the main function, this works.
Works ..
Not works , I got NRF_DRV_TWI_EVT_DATA_NACK error..
and I cannot call "nrf_drv_twi_tx" in the timer event handler...
Hi everyone, I am testing out the qspi flash on pca10056. While the read speed is decent around 650 KBs, the write speed is too slow ~ 35 KBs. It could be our own usb/caching...
There is an example in the SDK v15 folder. " ble_app_buttonless_dfu "
I write a custom firmware which has ble interface sending temperature data.
I want to add ble bootloader...
Hi,
I'm using the S132 v6.0 and SDK v15.0 to work with nRF52832. I found the it just get the advertising data. If the device put some data into the scan response, when I...
Hi,
I want to use nRF52840 USB dongle in my setup with other PCA10056 boards. I have seen that in link https://www.nordicsemi.com/eng/Products/nRF52840-Dongle it is mentioned...
Need to upgrade bootloader by application code. I have finished to program bootloader image to FLASH. Content is verified correct, comparing to SRC. However, the bootloader...
I have 2 52840 modules with PCB antenna and I am trying to check the max connection range
I followed the recommendations and achieved only 120m.
I cannot use the examples...
Hi, we recently using audio with ATVV service instead of HID service. As we notice, Audio would enable by SR3 itself in ATVV service if we push the key, but not in HID service...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
