Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi all,
In our project we are using nrf52810, SDK 15.0.0 and ble_app_uart.c example.
We are using our custom board in which MCU is communicating with BLE through wired...
Hello,
So i found this code from one of the earlier post which combines the saadc example with ble_app_uart example to make analog values from the analog pins to be sent...
Hello,
I want to use multiple timer interrupts, want to fetch values from 3 analog pins on every 20secs and then average three collected values at every 60 sec. so i would...
Hi currently I am handling a project in which I used nRF51822. I am using SDK 11 and softdevice SD130. I want to know is there any significant difference in power consumption...
How do I rename the Solution/Project from template_pca10040 to insert_name ?
I copy-pasted the template_project folder and renamed it
I changed the names in [SDK]\[SDK...
I have a nrf52 DK that I want to use to program the nrf52832 IC. I have bought a qfn48 adapter from here . I wish to use this adapter to place the IC then make connections...
Hi, all. I am in need of serious help. I need to set up a wireless mesh network using the nRF52840 SoC. It must have 9 nodes and be capable of multi-hopping. I need to set...
After configuring and enabling COMP, when READY event emits, is the RESULT register valid? Rephrasing the question: must you trigger the SAMPLE task to ensure RESULT register...
Hi, I've rebuilt so far with the help of multilink examples, the uart example that I can connect to two devices (According to the status of connection-led and the debug info...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
Hi,
I need to use
p_status->action == RELEASE_ACTION
to set the brightness level, but the p_status->action only gets updated after the loop finish so:
if (p_status...